304 / 304L Buttweld Fittings

Hind Metal is one of the pioneer whole sellers & dealers of 304 / 304L Buttweld Fittings, which is a molybdenum-bearing austenitic stainless steel that provides improved corrosion resistance. These Stainless Steel 304 Tee Pipe Fittings are non – magnetic in the annealed condition but may become slightly magnetic as a result of welding. Stainless Steel 304 Stub End Pipe Fittings have excellent corrosion resistance in a wide range of chemicals, especially in acidic chloride environments such as those encountered in pulp and paper mills. Increased levels of chromium, molybdenum, and nickel in these Stainless Steel 304 End Cap, improve resistance to chloride pitting and general corrosion. Resistance of Stainless Steel 304 Dish Cap Pipe Fittings increases with molybdenum alloy content, which is further resistant to sulphuric acid concentrations up to 5 percent at temperatures as high as 120 Degree F (49 Degree C). At temperatures under 100 Degree F (38 Degree C), this Stainless Steel 304 Long Radius Elbow has excellent resistance to solutions of higher concentration. However, service tests in Stainless Steel 304 Short Radius Elbow Pipe Fittings are recommended to account for the effects of specific operating conditions that may affect corrosion behavior. In processes where condensation of sulfur–bearing gases occurs, these Stainless Steel 304 Elbow Pipe Fittings are much more resistant to attack at the point of condensation than conventional alloy 316.
Hind Metal is one of the reputed producers and wholesalers of SS 304L Butt Weld Pipe Fittings, which can get marked up by fingerprints and grease, develop discoloration, and eventually rust. Stainless Steel 304L Pipe Fittings is an austenitic steel possessing a minimum of 18 % chromium and 8 % nickel, combined with a maximum of 0.08 % carbon. Stainless Steel 304L Elbow is nonmagnetic steel that cannot be hardened by heat treatment, but instead must be cold worked to obtain higher tensile strengths. As a result, Stainless Steel 304L Tee Pipe Fittings can be used in as–welded conditions, even in severe corrosive conditions. Stainless Steel 304L Reducer often eliminates the necessity of annealing weldments except for applications specifying stress relief. Stainless Steel 304L Long Stub End Pipe Fittings have slightly lower mechanical properties than Type 304. Stainless Steel 304L End Cap Pipe Fittings is non – hardenable by heat treatment, where annealing of heat is done up to 1900 Degree F – 2050 Degree F (1038 Degree C – 1121 Degree C), then cool rapidly. Thin strip sections of Stainless Steel 304L Dish Cap Pipe Fittings may be air-cooled, but heavy sections should be water quenched to minimize exposure in the carbide precipitation region. Stainless Steel 304L Short Stub End Pipe Fittings have very good draw ability, which can withstand much more time and abuse before showing signs of wear.
Hind Metal is one of the pioneer traders and dealers of SS 304H Butt Weld Pipe Fittings, which is unaffected by any of the weak bases such as ammonium hydroxide, even in high concentrations and at high temperatures. Stainless Steel 304H Elbow is generally highly resistant to attack from acids, but this quality depends on the kind and concentration of the acid, the surrounding temperature, and the type of steel. Stainless Steel 304H Tee Pipe Fittings are exposed to stronger bases such as sodium hydroxide at high concentrations and high temperatures will likely experience some etching and cracking, especially with solutions containing chlorides such as sodium hypochlorite. Stainless Steel 304H Cross Pipe Fittings are useful for storing and handling acetic acid, especially in solutions where it is combined with formic acid and when aeration is not present (oxygen helps protect stainless steel under such conditions). Stainless Steel 304H Reducer is also commonly used with formic acid though it will tend to discolor the solution, which further resists damage from aldehydes and amines. Fats and fatty acids only affect Stainless Steel 304H Stub End Pipe Fittings at temperatures above 150 Degree C (302 Degree F), and above are unaffected at all temperatures. Stainless Steel 304H Pipe Bend is required for processing urea, which is a relatively poor conductor of electricity, with significantly lower electrical conductivity than copper.